#grep -v '^[^a-z]*;?' /etc/asterisk/sip.conf
;
; SIP Configuration example for Asterisk
;
; Syntax for specifying a SIP device in extensions.conf is
; SIP/devicename where devicename is defined in a section below.
;
; You may also use
; SIP/username@domain to call any SIP user on the Internet
; (Don't forget to enable DNS SRV records if you want to use this)
;
; If you define a SIP proxy as a peer below, you may call
; SIP/proxyhostname/user or SIP/user@proxyhostname
; where the proxyhostname is defined in a section below
;
; Useful CLI commands to check peers/users:
; sip show peers Show all SIP peers (including friends)
; sip show users Show all SIP users (including friends)
; sip show registry Show status of hosts we register with
;
; sip debug Show all SIP messages
;
; reload chan_sip.so Reload configuration file
; Active SIP peers will not be reconfigured
;
[general]
context=default ; Default context for incoming calls
;allowguest=no ; Allow or reject guest calls (default is yes)
allowoverlap=no ; Disable overlap dialing support. (Default is yes)
;allowtransfer=no ; Disable all transfers (unless enabled in peers or users)
; Default is enabled
;realm=mydomain.tld ; Realm for digest authentication
; defaults to "asterisk". If you set a system name in
; asterisk.conf, it defaults to that system name
; Realms MUST be globally unique according to RFC 3261
; Set this to your host name or domain name
bindport=5060 ; UDP Port to bind to (SIP standard port is 5060)
; bindport is the local UDP port that Asterisk will listen on
bindaddr=0.0.0.0 ; IP address to bind to (0.0.0.0 binds to all)
srvlookup=yes ; Enable DNS SRV lookups on outbound calls
; Note: Asterisk only uses the first host
; in SRV records
; Disabling DNS SRV lookups disables the
; ability to place SIP calls based on domain
; names to some other SIP users on the Internet
;domain=mydomain.tld ; Set default domain for this host
; If configured, Asterisk will only allow
; INVITE and REFER to non-local domains
; Use "sip show domains" to list local domains
;pedantic=yes ; Enable checking of tags in headers,
; international character conversions in URIs
; and multiline formatted headers for strict
; SIP compatibility (defaults to "no")
; See doc/ip-tos.txt for a description of these parameters.
;tos_sip=cs3 ; Sets TOS for SIP packets.
;tos_audio=ef ; Sets TOS for RTP audio packets.
;tos_video=af41 ; Sets TOS for RTP video packets.
;maxexpiry=3600 ; Maximum allowed time of incoming registrations
; and subscriptions (seconds)
;minexpiry=60 ; Minimum length of registrations/subscriptions (default 60)
;defaultexpiry=120 ; Default length of incoming/outgoing registration
;t1min=100 ; Minimum roundtrip time for messages to monitored hosts
; Defaults to 100 ms
;notifymimetype=text/plain ; Allow overriding of mime type in MWI NOTIFY
;checkmwi=10 ; Default time between mailbox checks for peers
;buggymwi=no ; Cisco SIP firmware doesn't support the MWI RFC
; fully. Enable this option to not get error messages
; when sending MWI to phones with this bug.
;vmexten=voicemail ; dialplan extension to reach mailbox sets the
; Message-Account in the MWI notify message
; defaults to "asterisk"
;disallow=all ; First disallow all codecs
;allow=ulaw ; Allow codecs in order of preference
;allow=ilbc ; see doc/rtp-packetization for framing options
;
; This option specifies a preference for which music on hold class this channel
; should listen to when put on hold if the music class has not been set on the
; channel with Set(CHANNEL(musicclass)=whatever) in the dialplan, and the peer
; channel putting this one on hold did not suggest a music class.
;
; This option may be specified globally, or on a per-user or per-peer basis.
;
;mohinterpret=default
;
; This option specifies which music on hold class to suggest to the peer channel
; when this channel places the peer on hold. It may be specified globally or on
; a per-user or per-peer basis.
;
;mohsuggest=default
;
;language=en ; Default language setting for all users/peers
; This may also be set for individual users/peers
;relaxdtmf=yes ; Relax dtmf handling
;trustrpid = no ; If Remote-Party-ID should be trusted
;sendrpid = yes ; If Remote-Party-ID should be sent
;progressinband=never ; If we should generate in-band ringing always
; use 'never' to never use in-band signalling, even in cases
; where some buggy devices might not render it
; Valid values: yes, no, never Default: never
;useragent=Asterisk PBX ; Allows you to change the user agent string
;promiscredir = no ; If yes, allows 302 or REDIR to non-local SIP address
; Note that promiscredir when redirects are made to the
; local system will cause loops since Asterisk is incapable
; of performing a "hairpin" call.
;usereqphone = no ; If yes, ";user=phone" is added to uri that contains
; a valid phone number
;dtmfmode = rfc2833 ; Set default dtmfmode for sending DTMF. Default: rfc2833
; Other options:
; info : SIP INFO messages
; inband : Inband audio (requires 64 kbit codec -alaw, ulaw)
; auto : Use rfc2833 if offered, inband otherwise
;compactheaders = yes ; send compact sip headers.
;
;videosupport=yes ; Turn on support for SIP video. You need to turn this on
; in the this section to get any video support at all.
; You can turn it off on a per peer basis if the general
; video support is enabled, but you can't enable it for
; one peer only without enabling in the general section.
;maxcallbitrate=384 ; Maximum bitrate for video calls (default 384 kb/s)
; Videosupport and maxcallbitrate is settable
; for peers and users as well
;callevents=no ; generate manager events when sip ua
; performs events (e.g. hold)
;alwaysauthreject = yes ; When an incoming INVITE or REGISTER is to be rejected,
; for any reason, always reject with '401 Unauthorized'
; instead of letting the requester know whether there was
; a matching user or peer for their request
;g726nonstandard = yes ; If the peer negotiates G726-32 audio, use AAL2 packing
; order instead of RFC3551 packing order (this is required
; for Sipura and Grandstream ATAs, among others). This is
; contrary to the RFC3551 specification, the peer _should_
; be negotiating AAL2-G726-32 instead :-(
;matchexterniplocally = yes ; Only substitute the externip or externhost setting if it matches
; your localnet setting. Unless you have some sort of strange network
; setup you will not need to enable this.
;
; If regcontext is specified, Asterisk will dynamically create and destroy a
; NoOp priority 1 extension for a given peer who registers or unregisters with
; us and have a "regexten=" configuration item.
; Multiple contexts may be specified by separating them with '&'. The
; actual extension is the 'regexten' parameter of the registering peer or its
; name if 'regexten' is not provided. If more than one context is provided,
; the context must be specified within regexten by appending the desired
; context after '@'. More than one regexten may be supplied if they are
; separated by '&'. Patterns may be used in regexten.
;
;regcontext=sipregistrations
;
;--------------------------- RTP timers ----------------------------------------------------
; These timers are currently used for both audio and video streams. The RTP timeouts
; are only applied to the audio channel.
; The settings are settable in the global section as well as per device
;
;rtptimeout=60 ; Terminate call if 60 seconds of no RTP or RTCP activity
; on the audio channel
; when we're not on hold. This is to be able to hangup
; a call in the case of a phone disappearing from the net,
; like a powerloss or grandma tripping over a cable.
;rtpholdtimeout=300 ; Terminate call if 300 seconds of no RTP or RTCP activity
; on the audio channel
; when we're on hold (must be > rtptimeout)
;rtpkeepalive=<secs> ; Send keepalives in the RTP stream to keep NAT open
; (default is off - zero)
;--------------------------- SIP DEBUGGING ---------------------------------------------------
;sipdebug = yes ; Turn on SIP debugging by default, from
; the moment the channel loads this configuration
;recordhistory=yes ; Record SIP history by default
; (see sip history / sip no history)
;dumphistory=yes ; Dump SIP history at end of SIP dialogue
; SIP history is output to the DEBUG logging channel
;--------------------------- STATUS NOTIFICATIONS (SUBSCRIPTIONS) ----------------------------
; You can subscribe to the status of extensions with a "hint" priority
; (See extensions.conf.sample for examples)
; chan_sip support two major formats for notifications: dialog-info and SIMPLE
;
; You will get more detailed reports (busy etc) if you have a call limit set
; for a device. When the call limit is filled, we will indicate busy. Note that
; you need at least 2 in order to be able to do attended transfers.
;
; For queues, you will need this level of detail in status reporting, regardless
; if you use SIP subscriptions. Queues and manager use the same internal interface
; for reading status information.
;
; Note: Subscriptions does not work if you have a realtime dialplan and use the
; realtime switch.
;
;allowsubscribe=no ; Disable support for subscriptions. (Default is yes)
;subscribecontext = default ; Set a specific context for SUBSCRIBE requests
; Useful to limit subscriptions to local extensions
; Settable per peer/user also
;notifyringing = yes ; Notify subscriptions on RINGING state (default: no)
;notifyhold = yes ; Notify subscriptions on HOLD state (default: no)
; Turning on notifyringing and notifyhold will add a lot
; more database transactions if you are using realtime.
;limitonpeers = yes ; Apply call limits on peers only. This will improve
; status notification when you are using type=friend
; Inbound calls, that really apply to the user part
; of a friend will now be added to and compared with
; the peer limit instead of applying two call limits,
; one for the peer and one for the user.
; "sip show inuse" will only show active calls on
; the peer side of a "type=friend" object if this
; setting is turned on.
;----------------------------------------- T.38 FAX PASSTHROUGH SUPPORT -----------------------
;
; This setting is available in the [general] section as well as in device configurations.
; Setting this to yes, enables T.38 fax (UDPTL) passthrough on SIP to SIP calls, provided
; both parties have T38 support enabled in their Asterisk configuration
; This has to be enabled in the general section for all devices to work. You can then
; disable it on a per device basis.
;
; T.38 faxing only works in SIP to SIP calls, with no local or agent channel being used.
;
; t38pt_udptl = yes ; Default false
;
;----------------------------------------- OUTBOUND SIP REGISTRATIONS ------------------------
; Asterisk can register as a SIP user agent to a SIP proxy (provider)
; Format for the register statement is:
; register => user[:secret[:authuser]]@host[:port][/extension]
;
; If no extension is given, the 's' extension is used. The extension needs to
; be defined in extensions.conf to be able to accept calls from this SIP proxy
; (provider).
;
; host is either a host name defined in DNS or the name of a section defined
; below.
;
; Examples:
;
;register => 1234:password@mysipprovider.com
;
; This will pass incoming calls to the 's' extension
;
;
;register => 2345:password@sip_proxy/1234
;
; Register 2345 at sip provider 'sip_proxy'. Calls from this provider
; connect to local extension 1234 in extensions.conf, default context,
; unless you configure a [sip_proxy] section below, and configure a
; context.
; Tip 1: Avoid assigning hostname to a sip.conf section like [provider.com]
; Tip 2: Use separate type=peer and type=user sections for SIP providers
; (instead of type=friend) if you have calls in both directions
;registertimeout=20 ; retry registration calls every 20 seconds (default)
;registerattempts=10 ; Number of registration attempts before we give up
; 0 = continue forever, hammering the other server
; until it accepts the registration
; Default is 0 tries, continue forever
;----------------------------------------- NAT SUPPORT ------------------------
; The externip, externhost and localnet settings are used if you use Asterisk
; behind a NAT device to communicate with services on the outside.
;externip = 200.201.202.203 ; Address that we're going to put in outbound SIP
; messages if we're behind a NAT
; The externip and localnet is used
; when registering and communicating with